Work Hours

DateWorkOskar (hours)Simon (hours)
2012.11.15-2013.6.1Plan, Budget, Contract5050
2013.7.3Got delivery from EVE (controller box, electric motor, and vakuum pump) and repported missing stuff (curtis gauge, power cables, multipole connector, potentiometer, manual, switches)4
2013.9.4Sand blasted two rims. Painted them too4
2013.9.8Sand blasted two rims. Painted them too. Fetched sand from forest.5
2013.9.9Begun to veld and fix rusted areas under the front window.3
2013.9.10Welded rust3
2013.9.13Welded rust. Fixed dent.26
2013.9.14Welded rust. front window done. Removed windscreens.34
2013.9.20Started to repair damaged section rear, and under windows. Removed seats and other stuff.5.56.5
2013.9.21Repair on the damaged section aft. Started to mesh two trunk hatches to one. Organized stuff from the car.66.5
2013.9.22Worked with the trunk hatch. Started on our own blog36
2013.9.23Same again3.5
2013.9.24Trunk hatch done and mounted. Adjustments to the repaired section rear to match the repaired trunk hatch. Measured gearbox and electric motor dimensions.66
2013.9.27Welded on the sliding door. Grinded away rust in the engine compartment. Test mounted driver seat44
2013.9.28Sliding door done. Welded shut unused hatch inside the car. Fixed engine lid. Grinded in the engine compartment.5.57
2013.9.29Welded shut holes. Planned the ventilation system. Removed old junk under the car. Removed windows from doors. Working with driver seat.46.5
2013.9.30Welded holes from old ventilation system. Cleaned the workshop.2
2013.10.1Repaired beam under the car. Grinded in engine compartment and working with driver seat.44
2013.10.2Repaired beam under car. Painted.2.5
2013.10.3Welded away small holes from VW-badge. Driver seat now ok. Meeting with Michael from PAF. Delivery from EVE: Multipole connector, circulating pump for cooling and some switches. (Now mising: manual, potentiometer, powercables)1.51.5
2013.10.5Grinded in the engine compartment.4
2013.10.6Grinded in the engine compartment. Started to repair left side panel, lower section.49
2013.10.7Bought steel from the neighbour workshop. Manufactured new lower left side panel and prepaired to mount it.3
2013.10.8Tried to mount panel, but had problem with old damage covered with TIN!!!! Grinding work.44
2013.10.9Repeared left wheelhouse. Prepared welding of holes inside the car.67.5
2013.10.11Welded shut holes inside the car. Finished our own blog43
2013.10.12Same again. Started to remove rusted metal from beams in the engine compartment. Polished door handle.66
2013.10.13Constructed new sheets of metal, and velded them into place in the engine compartment. Repeared sliding door. Tried to dismount the sliding door handle.3.56
2013.10.14Grinded the veld from yesterday and velded shut holes in the engine compartment. Painted it all gray. Bought steel sheet from the neighbour workshop.5
2013.10.15Got repair parts delivered from Paruzzi. Started to mount panel under engine lid. Installed suspension front left.33
2013.10.16Panel from yesterday done. Begun to work with the drivers step and floor (which was all rusted). Sand blasted left brake caliper. Checked other brake components.612
2013.10.17Welded floor, inner step and outer step on the drivers side (and some major repear inside the wheelhouse). Unscrewed the two rear hub nuts (required some heating). Test mounted rear brakes and found out that some parts were not ordered. Manufactured connector for pressurized air for the brake calipers, since the pistons were rusted. Did not help.89.5
2013.10.18Grinded the velded areas from yesterday. Started to change the left door outer panel. Worked with gear shifter and shift rod etc.68
2013.10.19Worked with the door panel. Updated blog23
2013.10.20Left door panel done. Tested and dismounted gear box.8.58.5
2013.10.21Fixed the gear rod.3
2013.10.22Renovated brake calipers. One piston broke. Must try to fix a new one, othervise order a new caliper. Fixing on the blog. Updated this table with everything above.37.5
2013.10.25Meeting with our supervisor from the school. Then fixed rusted area on passenger side floor and step. Fixed the rusted parts of the door too. Fixed error on blog. Fixed left front brake and started to remove old brake lines.89.5
2013.10.26Removed rusted panel under the sliding door. Repaired rusted metal behind the old panel and then Welded the new panel into place. Fixed front left brake. Cleaned the gear box.4.58
2013.10.27Constructed a new body panel lower part for the front right wheel house. Updated the blog14
2013.10.28Cut away lower part of right rear side panel and corner and battery tray (new parts are going to be welded into place soon). Started to repair rusted part of the right rear wheelhouse.4
2013.10.29Meeting with Lasse and Basse. Discussed how to connect motor and transmission the best way. Received clutch assembly. Welded battery tray into place.46.5
2013.10.30Prepared welding of left side panel. Took some messurement of the gearbox and motor for the adapterplate3.54
2013.11.1Started to put in the new brake lines. Prepared Welding job.33
2013.11.2Continued with the brake lines. Welded left side panel.68.5
2013.11.3Took away the drive shafts and fixed one brake line. Did the last stuff on the left side panel. Started to repair damaged (read gone) section behind right side panel before welding of the new right side panel.59.5
2013.11.7Repair of the damaged section done.1.5
2013.11.8Worked with the right side panel (ready for welding now). 25
2013.11.9Welded on side panel. Messured and planned the adapterplate33
2013.11.10Welded the inside of the new right side panel. Grinded the weld. Repaired a rusted spot on the right side and one in the front of the car. 6
2013.11.11Welded right rear corner into place. Had to make a couple of adjustments to the new corner panel due to poor fit. Updated the cad drawing36
2013.11.12Updated the blog. Started to fix on the vacuum system. Grinded the weldings from yesterday. Welded new fastenings for right rear lamps. Took measurements for the new left middle side panel (lower part).64.5
2013.11.13Bought steel from the neighbour workshop. Started to make a whole new lower left side panel (because of what happend 2013.10.8)2.55.5
2013.11.14Worked with the left side panel.3
2013.11.15Welded side panel.1
2013.11.16Welding of side panel done. Grinded the weld. All major body work welding done.3.5
2013.11.18Installed the vacuum pump. Welded shut the old petrol cap. Worked with corrosion protection.23.5
2013.11.19Worked with corrosion protection and water sealing.4.5
2013.11.20Worked with corrosion protection and water sealing.1
2013.11.22Worked on the controller3
2013.11.23Worked on the controller, updated the blog3
2013.11.26Worked on the controller3
2013.11.27Worked on the adapterplate22
2013.11.28Worked on the adapterplate22
2013.11.30Worked on the controller2
2013.12.1Worked on the controller2
2013.12.03Worked on the adapterplate. Got a cooler at the junkyard3.53.5
2013.12.11Tested cooling fan and thermostat temperature limits. Dismounted and repaired clutch disengage arm and adjusting nut. Planned mounting of the throttle. Controller work.12.5
2013.12.22Worked on the controller3
2013.12.27Updated the blog.2
2014.01.11Worked with adapter plate in cooperation with Basses Motor.0.56
2014.01.26Worked on the controller3
2014.01.30Total work hours with the "electric cars" survey210.5
2014.02.02Finnished the major work on the coupling betweem the electric motor and the gearbox in cooperation with Basses Motor. NICE! Updated the Blog28
2014.02.03Paper work, mail and ordering parts5
2014.02.04sent "electric cars" survey to 280 companies. Tried to recieve energy data about Ă…land. Trying to get batteries for testing out the controller and electric motor.3
2014.02.05Preparations for the writing process22
2014.02.07Preparation for testing of motor and controller2
2014.02.08Tested electric motor and controller. Did not start. Probably need another potentiometer for the regenerative braking funktion...66
2014.02.10Succesfully tested motor and controller. The problem was an interlock function that needed an input signal.3.53.5
2014.02.12Updated the blog3
2014.02.16Preparing for tomorrow.33
2014.02.17Worked on the controller mounting, brake system and went to basse for the last adjustment on the adapter plate.11.511.5
2014.02.18Finnished with the controller mounting. Tested the adapter plate. Decided it needs to be balanced.7.57.5
2014.02.19Started to change oil on the transmission but found a problem so now we need to open it and check. Sent the adapter plate to be balanced.3.53.5
2014.02.20Worked on the transmission. Mounted the transmission and motor in the car for some messurements.5.55.5
2014.02.23Updating the blog, and worked on our paper. Worked on motor holder.55.5
2014.02.27Worked on paper2
2014.03.01Finished the work on the new motor holder. Working on the paper.58.5
2014.03.03Worked on paper2
2014.03.7Transported the batteries to the workshop.Meeting with Michael and Lackcenter.54
2014.03.8Worked on the paper6
2014.03.9Worked on the paper2
2014.03.13Prepared the car for the blastring and tested the batteries. 99
2014.03.14Finished the testing on the batteries.2
2014.03.15Worked on the paper4
2014.03.16Worked on our paper. Brought back the car after soda blasting67
2014.03.17Updated the blog. Worked on the paper65
2014.03.18Cleaned the car from the soda.4.5
2014.03.19Worked on the paper4
2014.03.22-24Worked on the paper66
2014.03.25Worked on the paper2.5
2014.03.26Worked on the paper2
2014.03.27Working on the brakes.55
2014.03.28Preparing for the paint. Built on battery box.6.56.5
2014.03.29Preparing for the paint. Built on battery box.6.56
2014.03.30Wrote the examination meeting minutes and sent it to Kjell Dahl and Oskar.0.5
2014.03.31Tested balanced fly wheel, and transmission together. Worked nice. Tested 96V charger with no luck. Manual reading in progress.65.5
2014.04.1Preparing for the paint. final mounted the electric motor, flywheel, clutch and gearbox.6.53
2014.04.2Preparing for the paint.6.5
2014.04.4Preparing for the paint. Borrowed a seat from PAF over the weekend to finnish battery box and fastenings. bought wood board and steel.8.58
2014.04.5Preparing for the paint. Finnishing the work on the paper76.5
2014.04.6Preparing for the paint. Updating the blog. worked with the final touch on the paper. Built on the battery box.610.5
2014.04.7Working on the presentation. Cleaned the work shop.3.52.5
2014.04.8Battery box. Filling up brake system with brake fluid.35.75
2014.04.9Battery box. Preparing for the paint.3.53
2014.04.10Battery box welding and painting. Assisted Per Erik with metal job.58
2014.04.11Meeting with PAF. Built mountings for liquid cooler. Made fastenings for the 12V system batteries. Painted battery box the last time.6.57
2014.04.12Painted the motorhold.4.5
2014.04.13Repared all the holes in the car floor. Painted a little. Welded shut a hatch that was cut open for Per Erik the metal master.7
2014.04.14Preparing for the paint. found out why the 96V charger was not working (lets call it bad connection...)52.5
2014.04.15Preparing for the paint.85.75
2014.04.16Preparing for the paint.8
2014.04.17 & 19Assembled the gas pedal mechanism with metal vire etc. worked, but bad "feel" in the gas pedal. Going for plan B.9.5
2014.04.20Preparing for the paint.5.5
2014.04.21Preparing for the paint. Made new gas pedal mount. started to make new wooden sheets for interior. Started to correct the examination paper.77.5
2014.04.22Corrected paper. Made the rest of the wooden sheets for interior.54.25
2014.04.23Corrected paper, just some small touches left. Applied grease at grease points on VW-bus. Delivered seat and interior sheets to PAF.4
2014.04.24Straightened out the rear bumper from hell.4
2014.04.25Final touch on examination paper. sent it away to swedish teacher.1.5
2014.04.27Started on the opposition of our classmates paper. 5
2014.04.28Worked on our presentation. Grinded plastic23
2014.04.29Preparing for the paint.32.25
2014.04.30Preparing for the paint. Straightened out front bumper.44.75
Total amount of hoursOskar (hours)Simon (hours)
1109.25499610.25

No comments:

Post a Comment